Diamond Audio Technology D7402 Specifications download pdf

LOWPASS ON/OFF

Pushing this button “IN” engages the Lowpass filter. Pushing this button

“OUT” will bypass the filter.

LOWPASS FREQUENCY

Turning this control sets the Lowpass crossover point from 50Hz (fully

counterclockwise) to 5kHz (fully clockwise).

HIGHPASS FREQUENCY

Turning this control sets the Highpass crossover point from 50Hz (fully

counterclockwise) to 5kHz (fully clockwise).

HIGHPASS ON/OFF

Pushing this button “IN” engages the Highpass filter. Pushing this button

“OUT” will bypass the filter.

X-OVER OUT

This crossover is fully independent. Signal can be parallel routed from

the CH 1/2 INPUTS (X-OVER INPUT SELECT button set to the “IN”

position) or be directly sent to this crossover via the AUX. X-OVER INPUT

RCA jacks (X-OVER INPUT SELECT button set to the “OUT” position).

This configuration allows the AUX. crossover to be used with a separate

amplifier not equipped with its own on-board crossover for the ultimate in

system flexibility.

Note: By engaging both Highpass and Lowpass filters and setting the desired

crossover points, a Bandpass filter can be created:

AUXILIARY CROSSOVER

Signal can be routed from the channel 1/2 INPUTS (X-OVER INPUT

SELECT button set to the “IN” position) or combined with the CH 3/4

INPUTS (X-OVER INPUT SELECT button set to the “OUT” position).

These signals can then be processed by the third (AUXILIARY) crossover.

This additional independent crossover can be used with a separate amplifier

not equipped with its own on-board crossover for the ultimate in

system flexibility.

D7 CROSSOVER FREQUENCIES

Diamond Audio D7 Professional Reference Series Amplifiers feature fully

variable crossovers. The frequency control knobs (located in the tray on the

top of the amplifier) are labeled 50Hz when the knob is rotated fully counter-

clockwise (left) and 5kHz when rotated fully clockwise (right).

To make basic setting of the crossover frequencies a little easier, we’ve

come up with the following rotational diagram:

HIGHPASS/LOWPASS

FREQUENCY

Notice that the outer most circle of numbers (1:00, 2:00, etc.) represent

numbers as they appear on the face of a clock. The number underneath each

“hour” designation on the simulated clock face is the approximate crossover

frequency at that position.

BRIDGING

All pairs of Diamond Audio D7 amplifier channels are capable of being

bridged to a 4 Ohm mono output. Creation of the mono channel is accomp-

lished by using the left channel positive (+) output connection of the amplifier

for the speaker positive and the right channel negative (-) output connection

of the amplifier for the speaker negative.

D7152 and D7402 manual #135.p65 8/30/2002, 2:24 PM10

1 2 3 4 5 6 7 8 9 10

? Channels 1/2 Lowpass to a 7

Summary of Contents

Page 1

10LOWPASS ON/OFFPushing this button “IN” engages the Lowpass filter. Pushing this button“OUT” will bypass the filter.LOWPASS FREQUENCYTurning this con

Page 2

1FEATURES:TECHNICAL? Symmetrical Topology, Fully Regulated, Triple-Split-Rail Power Supply? Isolated Input Section Utilizing “Quasi-Differential”Instr

Page 3

9Note: To set crossovers, first remove the two 1/16” Allen screws holdingdown the security cover using the Allen key provided. When reinstallingthe co

Page 4

8SPEAKER WIRINGDiamond Audio recommends using speaker wire of at least 16 gauge.Lay out the wire in the vehicle from the individual speaker locations

Page 5

7POWER CABLE GAUGE CHART14An additional temperature monitoring circuit protects the D7 amplifierunder extreme high power or extreme high-ambient tempe

Page 6

6TURN-ON CONNECTION (REMOTE)Locate the terminal labeled “REMOTE” between the ground and +12Vpower connection points on the end of the amplifier. Your

Page 7 - ? Channels 1/2 Lowpass to a

5to the bare metal using a bolt, star washer and nut. Seal the area from aboveand below to prevent rust. Strip approximately 1/2 inch of insulation fr

Page 8

4warranty. Mounting your amplifier inside an enclosure is not a good idea unlessthe enclosure is equipped with ventilation fans to circulate fresh air

Page 9

3INSTALLATIONTOOLS NEEDED FOR INSTALLATION? 1/16" Allen Key (Included): Crossover Security Cover Top Screws? 3/16" Allen Key: Up to 1/0 AWG

Page 10

2CONTINUOUS RMS OUTPUT POWERNote: Full Rated Power is generated at all voltages between 11 and 16VDC.D7152 D7402150W x 2 @ 4 Ohm Stereo 400W x 2 @ 4 O

Comments to this Manuals

No comments

Diamond Audio Technology D7402 Specifications

Browse online or download Specifications for Car audio amplifiers Diamond Audio Technology D7402. Diamond Audio Technology D7402 Specifications User Manual

Summary of Contents

Comments to this Manuals